Skip to main content

New Stockists And Catching Up


I've been busy recently making stock for two new stockists! I gave myself two weeks to make 22 pairs of earrings including earwires and oxidising and polishing them all and did it in just over a week working in the afternoons when I'd finished my part-time job. Am I the only one who likes to get things done and out of the way rather than have it hanging over me?!



Here's some of the enamel stuff cooling on my soldering block.
That is NOT our carpet!! It's the doormat by the back door where I took the photo cos it was nice and bright. Good forbid anyone should think that grubby, cat-hairy delight was gracing the entire floor :D


All the earrings were dutifully packed up and sent on their way and can now be found in ArtFully Made, a lovely gift shop run by Tamsyn Simmonds at 14 South Street, Wellington, Somerset and at Good Girl Designs, a shop run by Nicola Hunt at Area One, 2 Old Dairy, Twitter Lane Waddington, Clitheroe in Lancashire.


Catching Up
I've since been trying to catch up and add some new stock to my Folksy shop. I took almost half of it out of the shop for a wholesale order recently and I'm slowly getting there! I have a pile of earrings (14 pairs!) sat waiting for the sun to come out from behind this awful grey sky we've got at the moment. Thurday is looking good in the south east this week so fingers crossed.

Here's a few pairs I did manage to photograph before the grey gloom descended :



Tip: Don't buy a hot pink camera if you're going to photograph shiny things....seemed like a good idea at the time......



copper....


copper & enamel.....


more copper......
   

 experimenting with transparent enamels.....

Comments

  1. Beautiful! Love the copper and green enamel earrings.

    ReplyDelete
  2. Oooh, these are so rich and I'm drooling over on this side of the Pond, now! Beautiful colors!

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco