Skip to main content

Metal Wrap Beads


I'm always on the lookout for variations I can give my bangles and I came across some paper wrap beads recently and thought a metal version might work well on a bangle. I've never made paper beads but they start off as a long thin triangle shaped piece of paper that is then wrapped onto a thin rod and glued to create a bead.

Here's my attempt at a metal version. It's a bit long-winded and clumsy as I was making it up as I went along! {I've since worked out a much simpler way of doing it too :D}


I started with some 24g/0.5mm copper sheet that I rolled through the rolling mill to approx 0.35mm thickness. I cut out three different shapes for the beads and annealed them to soften the metal.


Using my fingers and a mallet I started to curl the end of the copper strip around a scrap piece of copper wire. I decided that the end needed to be fixed to the copper wire to make it easier to wrap the rest of the strip tightly around the wire.


So I flowed a small piece of solder in the curled part of the copper strip and another bit of solder at the end.


Ready for soldering to the wire.


After soldering the end to the wire I pickled the copper and wrapped the strip around the wire to form the bead.


The three different bead shapes after I soldered the end down and cleaned them up.
 I like the look of them and think the squared end I gave them makes a change from the normal pointed end you see on lots of these type of beads.

I think a bangle with three or four beads soldered in place around it is going to look nice especially using silver beads with copper and bronze bangles. I've since worked out a much less fiddly way to attach the end of the strip to the wire and also will need to add some solder along the length of the bead strip so the whole bead is soldered in place and doesn't wiggle sideways once the bead is wrapped around the wire and end soldered.

I'm keen to get cracking on making some bead bangles which I'll do once I clear my current orders so watch this space!

In the meantime I made myself a bead template to speed up the process and make things easier.









Copyright © 2016 Cinnamon Jewellery. All rights reserved.

Comments

  1. Amazing idea Tracy! I love the look of the paper wrapped beads. This method looks fantastic with metal.

    ReplyDelete
  2. I made similar metal some time ago but soon gave it up as I didn't like gluing the ends and I didnt think of soldering them until I read this post

    ReplyDelete
  3. Love this! Beautiful choices :) I have just done a post on my new blog about statement jewellery and would love for you to check it out :) My blog is called The Kara Edit and you can find it at sedakaraman.blogspot.com Thanks xxx

    ReplyDelete
  4. Great idea, I have to try this! Thank you! :)

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco